【官方微信小程序】
企业资料
广州鑫图科技有限公司
联系人：肖美（经理）
固 话：020-85667648
手 机：18820009114
产品搜索
| 型号 | GS-97U7 | 品牌 | Gstar |
|---|---|---|---|
| 产地 | 广东省广州市天河区 |
轨迹记录及 GPS 数据点校准等产品
可用于GLonass定位器
2.模块优点支持 AssistNow Online 和 AssistNow Offline 等 A-GPS 服务
GPS、GALILEO、SBAS（WAAS、EGNOS、MSAS、GAGAN）混合引擎
3、模块参数表
模块性能 | |
芯片 | ublox UBX-G7020-KT |
频率 | L1, 1575.42MHz |
协议 | NMEA 0183 v2.3 GALILEO L1 open service (with upgrade) Default:GGA,GSA,GSV,RMC Support:VTG,GLL,TXT ublox binary and NMEA Command |
可用波特率 | 1200,4800,9600,19200,38400,57600,112500 bps |
通道 | 56 |
Internal ROM | 3Mbit of ROM and 2Mbit of RAM |
灵敏度 | 跟踪:-162dBm 捕捉:-160dBm 冷启劢-148dBm |
冷启动 | 平均29秒 |
温启动 | 平均28秒 |
热启动 | 平均1秒 |
精度 | HorizontalPosition:Autonomous<2.5maverage, SBAS < 2.0m average Velocity: 0.1 m/s Timepulse signal: RMS 30 ns |
最大高度 | 18000 米 |
最大速度 | 515 m/s |
最大加速度 | ≦ 4G |
更新频率 | 1-10 Hz |
A-GPS | AssistNow on-line and off-line |
接口 | |
I/O Pins | 1 serial ports |
物理特性 | |
类型 | 18 pin stamp holes |
外形尺寸 | 10.1mm * 9.7 mm * 2.4mm |
电源 | |
电源 | 3.3VDC ±5% |
备份电压 | 1.8~3.6VDC |
耗电量 | 18~25mA |
工作环境 | |
湿度范围 | 5% to 95% non-condensing |
工作温度 | -40℃ to 80℃ |
储存温度 | -40℃ to 80℃ |
4、模块工作原理
5、模块信号测试图及RF射频属性图
6、模块管脚分配
Pin NO. | Pin Name | I/O | Description | Remark |
1 | GND | I | Ground | Assure a good GND connection to all GND pins of the module,preferably with a large ground plane. |
2 | TXD | O | Serial Port | UART, leave open if not used, Voltage level referred VCC_IO. Can be configured as TX-ready indication for the DDC interface. |
3 | RXD | I | Serial Port | UART, leave open if not used, Voltage level referred VCC_IO |
4 | TIMEPULSE | O | Timepulse Signal | Leave open if not used, Voltage level referred VCC_IO |
5 | EXTINT | I | External Interrupt | Leave open if not used, Voltage level referred VCC_IO |
6 | V_BCKP | I | Backup Supply Voltage | Backup supply voltage input pin. Connect to VCC_IO if not used. |
7 | VCC_IO | I | VCC_IO | IO supply voltage. Input must be always supplied. Usually connect to VCC Pin 8 |
8 | VCC | I | Supply Voltage | Provide clean and stable supply. |
9 | RESET | I | Reset | Reset |
10 | GND | I | Ground | Assure a good GND connection to all GND pins of the module,preferably with a large ground plane. |
11 | RF_IN | I | GPS signal input from antenna | The connection to the antenna has to be routed on the PCB. Use a controlled impedance of 50 Ω to connect RF_IN to the antenna or the antenna connector. DC block inside. |
12 | GND | I | Ground | Assure a good GND connection to all GND pins of the module,preferably with a large ground plane. |
13 | ANT_ON | O | ANT_ON | Active antenna or ext. LNA control pin in power save mode.ANT_ON pin voltage level is VCC_IO |
14 | VCC_RF | O | Output Voltage RF section | Can be used for active antenna or external LNA supply |
15 | V_ANT/NC | I | Antenna Bias Voltage | Connect to GND (or leave open) if passive antenna is used. If an active antenna is used, add a 10 Ω resistor in front of V_ANT input to the Antenna Bias Voltage or VCC_RF |
16 | SDA2 | I/O | DDC Pins | DDC Data. Leave open,if not used. |
17 | SCL2 | I | DDC Pins | DDC Data. Leave open,if not used. |
18 | Reserved | - | Reserved | Leave open |
